Build a Railroad Tie Retaining Wall

A large sloping backyard may look appealing, but once you start mowing this unusable side hill, you may consider the benefits of getting rid of it. Thus, the thought to build a railroad tie retaining wall comes in. Cutting a large part of a sloping yard out to make room for a livable, usable back yard is a possible solution with the addition of a retaining wall.

Steps

1. Bulldoze or dig a section of the dirt from the hill out to where you want to build a railroad tie retaining wall.
2. Level the ground along the entire stretch of hill (so the wall will sit flat) by packing it down evenly with your foot, Buy and Maintain a Shovel or a board. Place a level on the surface of the ground to make sure it is level along the entire stretch where the first layer of railroad ties will be placed.
3. Measure the entire length and height of the retaining wall with a tape measure. First measure the length from one end of where you want the wall to sit to the other. Next, measure up from the ground to determine how high you want the wall to be.
4. Lay the first set of railroad ties out along the prepared ground making sure the ends fit snugly together. Cut any excess off one end of a railroad tie to fit your area if needed.
   • Make sure your ties are sitting flush on the ground by setting a level on them periodically throughout the length of the wall to check.
5. Drill holes about 1 foot (30.48 centimeters) apart through all of the base railroad ties.
   • The hole must be big enough to fit a piece of rebar through. The rebar should be at least 2 feet (60.96 centimeters) long.
6. Put a piece of rebar in each of the holes and hammer it into the ground until the rebar is flush with the top surface of your railroad tie base.
   
   • • The rebar acts as your stabilization for the wall.
7. Start on the second layer once your first layer is in place and stabilized, set your second layer of railroad ties on the first making sure to stagger them like bricks so 2 meet in the middle of a railroad tie above and below it.
   • Use nails, L-brackets or rebar to secure each layer to the layer below before adding additional tie layers.
     
     
     • Each layer will need to be cut individually so the ends of each tie meet at different spots to avoid 2 ends meeting at the same point as the ties above or below it.
8. Add support to each level by filling in between the back of the railroad ties and the ground with stones. This will also help with Improve Drainage Around Pool Decks.

Tips

• Starting your bottom layer with a slight tilt towards the ground behind it can also help prevent the wall from tipping over as the hill moves behind it over time.
• Construction adhesive can be used between the layers of railroad ties as an alternative to nails, brackets or rebar.

Warnings

• Most railroad ties, even those sold as "reclaimed" at home improvement centers, contain creosote. The EPA states that creosote is hazardous, and has no safe use in or around the home. Handling the ties is hazardous to humans, and creosote can leach from the ties for many, many years to harm animals and contaminate ground water and plants. Locate untreated ties (some manufacturers are switching to safer methods than creosote), or use ties that are known to be treated with materials that are safer than creosote.

Things You'll Need

• Shovel or board
• Level
• Tape measure
• Hammer
• Drill
• Chainsaw
• Rebar
• Rocks or stones
• Railroad Ties
• Nails or L-brackets

Related Articles

• Build a Brick Wall
• Build a Dry Stack Retaining Rock Wall
• Construct a Block Retaining Wall

See also

• Build a Wood Retaining Wall
• Build a Brick Wall
• Make a Fake Rock Wall
• Render a Wall
• Build a Retaining Wall
• Build a Mortarless Concrete Stem Wall
• Construct a Block Retaining Wall
• Build a Dry Stack Retaining Rock Wall

What links here

• Build a Retaining Wall
• Build a Wood Retaining Wall
• Screen a Porch