Change the Blades on a Riding Lawn Mower

Keeping the blades sharp and in good condition on a riding lawn mower will increase fuel efficiency, give better mowing results, and extend the life of this expensive piece of lawn maintenance equipment. Here are steps and tips on how to do this project yourself.

Steps

  1. Check the condition of your mower blades to see if they need changing. If the blades are not significantly worn but are dull, they may only require sharpening. If, on the other hand, the airfoil built into the back of the blade is worn away, or the blade is bent or otherwise damaged, you probably need to replace it.
  2. Park the mower on a suitable work surface. Turn it off and lock the brakes or chock the wheels. Disconnect spark plug(s).
  3. Raise the mower deck to its highest setting to make it easier to access the blades.
  4. Raise the mower itself to allow room to get your tools underneath it. You need to make sure it is supported solidly, as riding lawn mowers are heavy, and you don't want to risk having it fall on you while you work on it. For greater safety, consider using a manufactured mower or tractor lift.
  5. Get the correct size wrench to fit the mandrel nut (or bolt) on your mower. You may also need a cheater pipe or other means of keeping the blade from turning while you remove the nut.
  6. Turn the nut (or Open a Rusty Bolt) counterclockwise to remove it from the mandrel shaft, then allow the blade to drop off. For blades that are tightly seated, you may have to pry the blade off or work it up and down to loosen it after the nut is removed.
  7. Take the old blade to a hardware store or mower repair shop to match it with the new blades you will install. Choose new blades to suit your own preferences – there are a number of different blades for each type mower, including enhanced discharging blades, mulching blades, and heavy duty blades.
  8. Compare blades at the store to make sure the offset, spline (if applicable), length, and other features match. Since there are many different brands and manufacturers of riding lawn mowers, making sure the blades you purchase fit your mower is critical for a successful project.
  9. Install the new blades on your mower. Be sure to install the blade right side up, as they may fit upside down. Generally, if the blade has an offset in it, the center will be in a higher position than the ends of the blade. Make sure the blade fits all the way onto the spline to prevent damaging it when the nut that secures it is tightened.
  10. Tighten the nuts that secure the new blade. You may have torque specifications for this step for your individual mower.
  11. Check the belts, pulleys, tensioners, and other parts of the mower deck assembly while you have the mower parked for servicing.
  12. Lubricate the mandrel bearings and other parts equipped with grease fittings before lowering the mower.
  13. Lower the mower off the blocks, and clean up/put away your tools.



Tips

  • When you have replaced the blade, keep the new one sharp; it will last much longer.
  • Sharp blades make mowing faster and more efficient, and extend the life of your equipment.
  • Keep your lawn clean. Hitting debris shortens the life of your mower's blades.
  • Aftermarket blades are often much less expensive and of equal quality to original manufacturer's parts.
  • Make sure that the spark plugs are not connected.
  • Some mowers have a parts list displayed on the mower itself to help select the right part for the job.

Warnings

  • Block the mower up solidly so it will not fall while working underneath it.
  • Mower blades have sharp edges, and with worn out blades, almost any edge can be sharp, not just the cutting edge.
  • Make sure blades are properly fitted on the mandrel so they do not slip or come loose.

Things You'll Need

  • New blades
  • Wrenches
  • Block to support the mower

Related Articles

  • Replace the Blade on a Husqvarna Lawn Mower
Retrieved from "https://kipkis.com/index.php?title=Change_the_Blades_on_a_Riding_Lawn_Mower&oldid=352110"