Create an RSVP MX for Pen Spinning

An RSVP MX is a pen modification which consists of a Pentel RSVP and a Pentel HGG (Hybrid Gel Grip). This pen modification invented by Kam is great for spinning.

Steps

  1. (materials at bottom of page)
  2. Take apart pens
      • Take the RSVP, unscrew the back cap (with ink tube), take the cap off, and remove the grip.
      • Remove the grip and the metal tip from the HGG.
  3. Put grip into cap
      • Put a little oil or water (optional) on the RSVP grip that you removed (not the HGG), then insert it into the cap of the pen. Make sure the end with the little ridge on the end goes in last. Push it in until it is about halfway past the mark in the center of the cap.
  4. Reverse the ink
      • Now you must reverse the ink on the RSVP, so it pokes out of the back cap instead of the front. To do this, a hole must be created in the back cap of the pen. Use a drill or some kind of heated sharp metal object (use gloves or pliers with hot metal!). Once you finish, insert the ink and screw it back onto the pen. Put on the cap.
  5. Put on the metal tip
      • Take the tip from the HGG and attach it onto the tip of the RSVP. If you wish, secure it with tape, preferably Teflon (which is widely available). It is strongly suggested that you secure the metal tip if you use a substitute for the HGG.
  6. Slide on the grip
      • Slide the HGG grip onto the RSVP, past the metal tip. Put it as far down as you like.
  7. Insert
      • You can roll up paper with designs on it and put it into the clear body of the RSVP for decoration (or to mark the balance point of the pen).
  8. Congratulations!



Tips

  • You can remove the writing on the barrel with a hard eraser, a coin, or by sanding it off.
  • -Zebra Jimnie Gel Roller
  • -Papermate G-Force
  • -Papermate Flexgrip
  • -Uni-Ball Signo
  • -Papermate Flexgrip Elite
  • -Pentel Hybrid H2 (same tip)
  • -Pentel Milky Gel Roller (same tip)
  • For the metal tip:
  • -Bic Atlantis
  • -Uni-Ball Gel Grip
  • Some common substitutes for the Hybrid Gel Grip are listed below:
  • RSVP pens are mainly available in North America, while an HGG is most likely to be found in Europe. If you do not have either of these, you can trade with someone or buy them online.
  • -Pilot G2 (That Is if You get It out)
  • -Papermate Profile
  • -Pentel RSVP (1 full grip + 1 partial grip)
  • -Zebra Airfit
  • -Zebra Sarasa

  • -Pilot Better Ballpoint
  • It is a good idea to remove the clip from the RSVP cap (and file/sand it, off course) because it can disrupt the flow of certain tricks.
  • -Bic Bicmatic
  • -Papermate Dynagrip
  • -Pentel Hybrid Gel Roller
  • For the grip:
  • -Pentel Forte
  • -Uni-Ball Signo DX

Warnings

  • Use caution when poking the hole through the end-cap of the RSVP. Hold the cap in place when drilling and use hand protection if handling a hot metal object.

Things You'll Need

    • 1 Pentel RSVP Pen
    • 1 Pentel Hybrid Gel Grip
    • Drill or hammer (with a sharp object)
    • Oil (optional)
    • Paper insert (optional decoration, goes inside the clear body of pen)
    • Teflon tape or other (optional)

Related Articles

Sources and Citations

You may like

Retrieved from "https://kipkis.com/index.php?title=Create_an_RSVP_MX_for_Pen_Spinning&oldid=353232"