Maintain Your Water Softening System

Abrasive ‘hard’ water contains high levels of calcium and magnesium, causing lime scale buildup and interfering with soap's ability to clean. For homes in some geographical locations, a water softener system is a vital household appliance. Modern water softeners can generally last for years with little maintenance, but regular checks and cleaning will improve their lifespan.

Steps

Maintaining the Brine Tank

1. Check salt levels at least once per month. Salt is an essential part of the water softening process, as it regenerates the resin beads to prepare them for more softening. The softener manual should instruct you on the ideal salt level. As a general rule, fill the tank at least half-full with salt, and keep it at least 3 inches (7.5 cm) above the water level. High salt levels (within 4 in/15 cm of the tank top) may improve efficiency, but reduce this to a lower level if you notice old salt clinging to the sides.
   • If you use block salt, it may be best to have a technician raise your water level to submerge the block completely.
2. Know what kind of salt to add. Your water softener manual will tell you whether your machine runs on granular, tablet, or block salt. Granular salt is the most common choice, because it dissolves most easily. Buy it in pellet form if possible, since ordinary salt crystals can easily clog the tank. There are also different grades of salt to choose between:
   • Rock salt (coarse salt) is cheap but contains more impurities, which decreases efficiency and dirties your tank, requiring more frequent cleaning.
   • Solar salt is much purer than rock salt.
   • Evaporated salt is the highest-quality option, but also the most expensive.
3. Break up salt bridges. Salt can form a solid layer or "bridge" in the brine tank. This prevents the loose salt on top from mixing with the water down below, preventing the softener from working. Push a long broom handle several times around the center of the tank, all the way to the bottom, to break up any solid layers that have formed.
   • Pouring hot water over the bridge makes it easier to break.
   • If you have repeated problems with bridging, use less salt, and let the salt drop lower between refills. Cleaning the brine tank should also help.
4. Dissolve mush. The salt can also form a mushy pile at the base of the tank, causing the water to rise around it instead of mixing in. You can use a broom handle to break this up if it forms a large mound. It also helps to scoop up the mush and dissolve it in a bucket of hot water, then pour it back into the tank.

Cleaning the Tank

1. Schedule the cleaning. Modern water softeners can go without cleaning for 5–10 years. Clean them only if your water has turned hard and the basic maintenance above doesn't fix the problem within a couple days. Older models (especially electric ones) can benefit from an annual cleaning.
2. Empty the tank. Use the bypass valve to shut off water intake. Siphon-Water or dump all water out of the tank, then dump out the salt and throw it away.
   • Keep the waste away from your garden, as salt kills plants.
   • Dissolve blocks or bridges of salt with hot water if needed.
3. Remove the brine grid from the base of the tank. Some models have a mesh platform at the base of the brine tank. Set this aside before cleaning.
4. Scrub with soapy water. Mix a generous amount of dish soap into one or two gallons (4–8 liters) of water. Pour it into the tank and scrub the entire interior with a long-handled brush.
5. Rinse the tank. Dump out the soapy water and rinse with plain water.
6. Clean the tank with bleach. Pour ¼ cup (60 mL) of household bleach and 2–3 gallons (8–11 liters) of water into the tank. Stir and let sit for fifteen minutes to sanitize the tank. Most organisms cannot grow in concentrated brine, but it's a good idea to make sure.
7. Rinse and refill. Rinse out the bleach thoroughly. If there was a grid in the tank, put it back. Replenish the tank with water and salt as normal.
   • Wait at least a couple hours before regenerating the tank, to give the salt time to dissolve.

Additional Upkeep

1. Exercise the valves. About once a month, adjust the bypass valve in to temporarily cut off the softener from your water supply. (The bypass valve is usually a rod you push in to block water flow.) Twist the intake and outtake valves to the off position, then back to their original position. Return the bypass valve to its old position. This keeps the valves in good working condition.
   • If a valve leaks or drips, disassemble it and replace any damaged washers or seals.
2. Flush with water softener cleaner. Once every few months, pour water softener cleaner into the brine tank, following label instructions. Manually start a regenerating process (or pour in the cleaner right before a scheduled regeneration). This helps keep the resin efficient and functional.
   • If your water has high iron levels or other issues that interfere with your softener, use a high-strength product, or buy an attachment that automatically adds a small amount of cleaner each time the system regenerates.
3. Clean the valve between the brine tank and resin tank. The nozzle and venturi valve between the tanks creates the suction that pulls water in to regenerate the system. Disassemble and clean these parts about twice a year, or whenever the brine tank gets clogged. Follow the exact instructions in your manual. Failing to relieve water pressure before disassembling the valve could damage parts or cause injury.
4. Troubleshoot a broken machine. If you have tried everything above and your water is still hard, go through this checklist:
   • Double check that the bypass valve is open, the regeneration timer is set, and that there are no kinks in the hoses.
   • Troubleshoot-Low-Water-Pressure.
   • If your household's water use has increased or your water has become harder, set the timer to regenerate more often.
   • If the computer display is not working, check that the circuit is powered and all wires and fuses are intact.
   • If all else fails, have a plumber investigate your resin tank. Your manual may provide instructions for how to check it yourself, but attempt it only if you are comfortable working with plumbing and electricity.

Tips

• If your water leaves rust stains on dishes or clothes, buy a specialized iron removal product to add to your brine tank.
• If a medical condition restricts your sodium intake, switch from sodium chloride (regular salt) to potassium chloride. Check the manual first to make sure your softener can handle it. When making this change, it's a good idea to increase the salt intake setting by 10%. Contact a technician if your machine does not have an easy way to do this. Alternatively, install a reverse osmosis filter to remove sodium from the softened water.
• If you live in an area of high humidity, it’s advisable to keep lower levels of salt in the tank and refill little and often. Warm, close conditions can contribute to the formation of a salt bridge, which prevents your system from working optimally because it prevents the salt from coming into contact with the water.
• When you clean out the tank of a traditional electric softener, make sure you allow all the salt in the system to dissolve before scrubbing thoroughly with soapy water and filling it back up again. This way you can be sure there’s no build-up of residue.

Things You'll Need

• Water softener
• Broom
• Soapy Water
• Salt
• Bleach
• Brush

Sources and Citations

• Cleaning instructions from WaterTech

See also

• Clean Tap Water
• Make a Water Filter
• Make a Water Purifier
• Desalinate Water
• Install a Water Softener
• Dechlorinate Water
• Choose a Home Water Filter
• Change a Franke Triflow Water Filter Cartridge