Unclog a Toilet

Toilet clogs seem to happen at the most inopportune moments. Fortunately, you can clear most clogs yourself without having to pay a plumber. Most clogs can be cleared with a good plunger or homemade drain cleaner made with hot water, baking soda and vinegar. For deeper clogs, try snaking the drain or using a wet/dry vacuum to do the job.

Steps

Plunger

  1. Keep the toilet from overflowing. If your toilet doesn't flush properly after one flush, don't flush again. This will cause more water to be pumped into the toilet bowl. Instead, take the lid off of the toilet tank and close the toilet flapper. Closing the flapper will keep more water from entering the bowl.
    • The flapper looks like a circular drain stopper attached to a chain.
    • The water in the tank isn't dirty, so it's fine to stick your hand inside to close the flapper.
  2. Prep the bathroom. In case splashing occurs, place newspapers or paper towels on the floor to soak up liquid. The paper will make for easier cleanup later. You should also turn on the ventilation fan or open a window to minimize foul odors.
    • If the clog is serious, put on a pair of rubber gloves. Toilets are unsanitary, but a good pair of rubber cleaning gloves will protect you from any germs within. Choose gloves that reach up to your elbows.
    • You may also want to put on an old set of clothing, just in case things get messy.
  3. See if you can clear the obstruction. If you can see the cause of the clog, reach in and remove it from the toilet if possible. If you can't clear it with your hands, but you know there's an object (such as a child's toy) causing the clog, skip the plunging and go straight to another method.
  4. Use a high quality plunger. It is important to use a large heavy-duty rubber plunger, either the ball-shaped type or one with a fold-out rubber flange on the bottom which forms a seal. Do not use the small cheap suction-cup type of plunger. These will often not work.[1]
    • If your plunger is not making a tight seal, try wrapping an old rag around the end of the plunger to stop any leaks.
    • Run the plunger under hot water before using it. This will soften it up, which will help with create a seal.
  5. Insert the plunger into the bowl. Make sure the plunger completely covers the hole. The plunger should be submerged in water to be effective. It is important to be pushing and pulling with water, not air. Add water from the sink to the bowl if necessary.
    • Pump the plunger over the hole. Start slowly at first, since the first plunge will push air into the bowl. Push down, then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain. It may take 15 to 20 times before the toilet unclogs.[1] Be patient, as long as you're sure there's no hard object, plunging alone often suffices. It might not work immediately but would often work after a few repeated efforts/flushing, with each effort constituting of dozens of plunging. .
  6. Flush the toilet to check the drainage. If the plunging eventually drains the bowl, but the clog is still blocking a free flow down the drain, leave the plunger in the bowl and fill the bowl with water again. Fill it to the point it is normally after a regular flush, then plunge again. Stubborn clogs might require you to do this a number of times.

Enzyme Product

  1. Purchase an enzyme waste removal product. Look for a product that contains a mixture of enzymes that liquify waste materials. These enzymes are used in septic systems to break down waste.[2]
    • Products of this sort can be usually be purchased at home improvement stores in or near the plumbing aisle. Enzyme waste removal is preferable to using a drain-clearing chemical because it will not harm your pipes or the environment.[2]
    • This method will only work on organic waste, not toys or other objects.
  2. Follow the instructions on the container. Pour the recommended amount of the enzyme product into the toilet bowl. You will typically be instructed to wait overnight for the enzymes to go to work on the clog. The toilet should drain once the clog has cleared.

Homemade Drain Cleaner

  1. Heat half a gallon of water. If the toilet tends to clog easily as the result of trying to flush too much waste, using a combination of hot water, baking soda and vinegar will often do the job as well as a commercial drain cleaner. Boil half a gallon of water, then let it cool for a moment while you add other ingredients to the toilet bowl.
    • Use at least half a gallon. A small amount of water won't work, since it won't have enough force to push through the clog.
    • The water should be no hotter than a hot tea you can drink comfortably. It should not be boiling, since very hot water can crack porcelain. You want to raise the temperature of the water passing around or pressing on the clog.
  2. Pour 1 cup baking soda and 2 cups vinegar into the toilet. The baking soda and vinegar create a chemical process that help to dissolve clogs. Distilled white vinegar is commonly used, but any type of vinegar will work. The mixture will fizz a great deal. [3]
    • If you don't have baking soda and vinegar on hand, try adding a few squirts of dish soap to the toilet bowl. The soap may help to loosen the clog. [4]
    • This method isn't likely to work for clogs caused by a hard obstruction, such as a toy.
  3. Pour the hot water into the bowl. Pour it from waist level, rather than right near the rim. The force of the water falling into the bowl can help to clear the clog.
  4. Let the mixture stand overnight. In the morning, the water should have drained. This homemade drain cleaner should successfully clear clogs caused by organic material. If the water won't flush on your second try, you may have hard obstruction causing the clog. Try using a wire coat hanger or a drain snake.

Plumbing Snake

  1. Purchase or borrow a plumbing snake. A plumbing snake (also sometimes called a "flexible cleaning tool" or "auger") is a flexible coil of wire that can "snake" through the curves of a drain and get deeper than a wire can. The best snake is a "closet auger" which is designed specifically to clear toilet clogs without damaging or staining the bowl. A plumber would likely use a closet auger.[1]
  2. Insert one end of the snake into the drain. Push down, feeding the snake further into the drain until you feel an obstruction.
  3. Twist and push the snake through the obstruction. The goal is to break up the obstruction into smaller pieces that can move through the pipes. It may take a few minutes of maneuvering to clear the obstruction. Once the water drains, flush to toilet to see whether it drains as quickly as normal.
  4. Snake in reverse. It may become necessary to remove the toilet and run the snake through in the opposite direction. This is especially true with hard obstructions that may have been flushed by a curious child. If a hard obstruction is known, and you are not comfortable removing and replacing the toilet, contact a plumber.

Wire Coat Hanger

  1. Unravel and straighten a wire coat hanger. Then wrap the end of the wire with a rag. Use duct tape to keep the rag in place. This will prevent the sharp end from damaging the porcelain in your toilet.[5] The wire hanger method will generally work if there is an obstruction in the first few inches of the drain.
  2. Stick the wrapped end of the wire into the drain. Once the wire is in the drain, twist it, push it, and maneuver it in a circular motion to clear the drain. If you can feel the obstruction, push against it. Keep going until the water begins to drain.
    • Make sure you're wearing rubber gloves as you do this. You may get splashed as you move the wire around.
    • If you can't feel an obstruction, and the toilet won't drain, the clog must be out of reach of the hanger. Try the plumbing snake method to clear it.
  3. Flush the toilet once the water has drained. The obstruction and dirty water should now be able to flow through the drain like normal. If the toilet is still slow to drain, the obstruction may have gotten pushed further back, out of reach of the hanger. In this case you'll need to use a plumbing snake to clear it.

Chemical Drain Cleaner

  1. Purchase a chemical drain cleaner. They're available at most grocery, hardware, and "big box" stores. Use this method only as a last resort. The chemicals used in drain cleaners are toxic to people and pets, corrosive to pipes. Also, chlorinated drain cleaner are very damaging to the environment.[6]
    • If you suspect that there is a hard obstruction, do not use a chemical solution. Instead, use a snake or call a plumber.
    • Only use chemicals that are specifically made for toilets. Using other drain cleaners may damage your toilet.
  2. Pour the specified amount into the toilet. Be sure you follow the manufacturer's instructions. Keep the lid down to prevent toxic fumes from filling your bathroom.[1]
    • Never use a plunger right after adding the drain-cleaning chemicals. The chemicals could possibly shoot back up onto your skin.
    • Make sure the bathroom is well ventilated so you won't inhale the chemicals.

Wet/Dry Vacuum

  1. Buy or borrow a wet/dry vacuum. If you have tried plunging and snaking to no avail, consider using a wet/dry vacuum. Do not use an ordinary vacuum cleaner––it must be the wet/dry variety that can cope with water.
  2. Empty the water out of the bowl using the vacuum. The bowl must be free of water and any other debris in order to vacuum out the obstruction.
  3. Place the end of the vacuum hose into the drain. Push it into the toilet bowl a few inches into the hole. Use just the flexible hose, rather than an attachment. Coil an old towel around the hole to create a seal around the drain.
  4. Turn on the vacuum. Use one hand to put pressure on the towels to create a good seal. Wait a moment or two for the vacuum to work. There's a good chance the vacuum can suck out the clog.

Tips

  • Regularly clean the jets around the toilet bowl's edge so that the toilet can flush at full power, making it less likely to clog. If you haven’t cleaned them in a while, you might need to carefully use a screwdriver to clear buildup.
  • Before a clog: If you see (or hear) water backing up in the sinks or showers whenever you flush, that means there's a deep clog that will eventually stop your toilet from working properly. Don't bother with the above methods. Call a plumber.
  • If the toilet gets clogged often, try to figure out what clogged the toilet and prevent it from happening again. Common culprits are too much toilet paper, tampons (some are flushable but most are not), toys (both kids and pets are suspects), cotton swabs, and baby wipes. Consider having a little "what not to flush" presentation in the best interest of your plumbing.
  • Clean up diligently. Disinfect the toilet bowl with a disinfectant cleaner after you've cleared the clog. Dispose of the wire (if used) and disinfect or dispose of the rubber gloves and any other tools (such as a plunger or snake) that you used. These tools can spread germs and start to stink if not properly cleaned. A used plunger (especially flange plungers) may still have water inside of it after plunging. Keep it over the toilet, turn it a bit, and shake it slightly to drain it so it won't drip on the floor.
  • A mop with a plastic carrier bag over the head of the mop works great as an alternate plunger.

Warnings

  • Coat hangers and drain snakes can scratch the porcelain of the toilet. Try to be careful to minimize the damage, at least in the visible part of the bowl. The end of the coat hanger you are going to introduce in the toilet to "fish" the clog, should be given a v-shaped hook by using some appropriate pliers and then covered lightly with electrical tape. Proceed with greatest caution to engage the hook onto the clog/toy and then softly pull it out in a continuous motion.
  • Drain-cleaning chemicals are generally extremely toxic and hazardous. Avoid contact with skin and eyes, and do not mix chemicals. Follow all manufacturer instructions to the letter, and heed all warnings.
  • Do not push or pull the plunger violently when it is in the toilet bowl as it is unnecessary and will cause splashing.
  • Most drain cleaners available in retail stores for home use are not appropriate for toilets. Check the product label to ensure the product is compatible for use with toilet drains. Bear in mind that some drain cleaners produce a great amount of heat as a chemical reaction in contact with water; this heat if not handled properly might damage seriously the toilet and the plastic pipe attached to it.

Related Articles

Sources and Citations

  1. ↑ 1.0 1.1 1.2 1.3 http://www.familyhandyman.com/plumbing/toilet-repair/how-to-fix-a-clogged-toilet/view-all
  2. ↑ 2.0 2.1 http://www.nytimes.com/2009/12/24/garden/24fix.html?pagewanted=all&_r=0
  3. ↑ http://www.realsimple.com/home-organizing/home-organizing-new-uses-for-old-things/baking-soda-drain-unclogger
  4. ↑ http://www.artofmanliness.com/2009/09/03/how-to-unclog-a-toilet/
  5. ↑ http://www.drainsupport.com/how-to-unclog-a-toilet/
  6. ↑ http://www.nytimes.com/2009/12/24/garden/24fix.html?pagewanted=all&_r=0
Retrieved from "https://kipkis.com/index.php?title=Unclog_a_Toilet&oldid=293919"