Change a Lightbulb in a Recessed Light

A recessed light bulb lies flush with the ceiling or other surface, making it nearly impossible to grab and unscrew it by hand. As with so many other problems where you need to get a grip, duct tape is one of the easiest solutions. If this doesn't work, you may have to try a few different approaches to remove the retaining collar around the bulb.

Steps

Using Duct Tape

  1. Wait until the bulb is cool. If the light was recently on, wait until it is cool to the touch. This shouldn't take more than five minutes for a normal light bulb. Halogen lights may take twenty minutes.[1]
  2. Tear off a strip of duct tape. The strip should be about 12 inches (30 cm) long, or half as long as your arm.
  3. Fold over each end of the duct tape. Fold a short section of the duct tape over and stick it to itself. Repeat on the other side. These folded "handles" should be long enough for you to grip, with a sticky segment in between them.[2]
    • If you find it easier, you can wrap the duct tape in a circle instead, with the adhesive on the outside. Make the circle large enough to fit your hand through it.
  4. Stick the duct tape to the light bulb. Hold the handles of the duct tape and press the sticky segment against the flat surface of the recessed bulb.
  5. Twist to unscrew. Once the tape sticks to the light bulb, you should have enough leverage to get it loose. Almost all light bulbs use standard screw threading, so turn the bulb counterclockwise to unscrew it.
    • If it doesn't budge, read the method below for help removing the surrounding collar.
  6. Finish unscrewing by hand. Once the light bulb has emerged enough for you to grip the sides, pull off the duct tape. It's faster at this point to spin the bulb out by hand.
  7. Replace the light bulb with the same method. Screw in the new light bulb as far as you can by hand. When it's nearly flush, stick on the duct tape and turn clockwise to tighten to a secure fit.

Removing a Retaining Collar

  1. Turn off the light. Let the bulb cool to room temperature before you handle it.
  2. Look for a metal ring around the light bulb. Many recessed fixtures hold the bulb in with a metal collar. These are often removable, but follow the instructions below to avoid damaging your ceiling.
    • This is not necessarily the large ring that holds in the entire fixture, although it can be. Look closely for a second ring flush against the light bulb.[1]
  3. Cut away paint if necessary. If someone has painted over the ring, it may rip away pieces of drywall when you unscrew it. To avoid this, cut the paint around the ring with a utility knife, working it against the collar.[3] Now try the steps below until you find one that works for your model.
  4. Look for a screw or button. If you're lucky, your collar is simply held in place by a couple of screws. Some models have a small metal button, which you push or slide sideways to free the fixture.[4]
  5. Test whether the collar twists or pulls out. Some models can be twisted or pulled out by hand. Use light pressure only, unless you have confirmed this is the intended approach with a manual or the manufacturer. Here are two examples of light fixtures you can remove this way:
    • Modern recessed halogen lights often have a plastic collar with three tabs. Press your fingers against these tabs and rotate counterclockwise. Once you have access to the bulb, grip the base and the wire and wiggle them apart.[5]
    • Some recessed LED light fixtures can be pulled directly out of the ceiling. Watch your fingers, as a sharp metal clip will pop downward from the edge as the fixture emerges. You can then unclip the bulb from the wire.[6]
  6. Pry out the ring with a screwdriver. Some older halogen fixtures use a small, toothed, metal ring with no special fastener. Carefully insert a flathead screwdriver in between the ring and the light bulb, and pry outward. There is a gap in the ring, so you can flex it outward and carefully pull it down with your fingers. Grip the base of the bulb and gently wiggle the two prongs out of the socket to remove it.[1]
    • Take care not to chip the glass with the screwdriver.
  7. Remove a stuck ring. If there is no obvious fastener for the ring, but it refuses to twist out, it may be jammed. Try gently pushing up on the light bulb with a couple fingers from each hand. If the bulb recesses further into the ceiling, press your fingers outward against opposite sides of the ring. Try to rotate the ring while pressing to improve your grip.[7]
    • If this still doesn't work, and your model has three small tabs on the plastic collar, grip one of the tabs with a pair of pliers. Push with the pliers as you push another tab by hand.[8]



Tips

  • For lights in tall places, pick up a bulb changer pole from a hardware store. Choose a model with a suction cup end to grip the light.

Warnings

  • To avoid an electric shock, make sure the light is off before you insert the new bulb.

Things You'll Need

  • Recessed light bulb
  • Duct tape

Related Articles

Sources and Citations