Grout a Tile Floor

After tile is installed, the next step is grouting the gaps between tiles. This task is less time-consuming and labor intensive than installing tile, but it's even more important than making sure all your tiles are straight and look nice. Doing a proper grout job will ensure that the floor under the tile stays safe from moisture. You will still be working on your knees for an extended period of time, so it's not a job to take lightly.

Steps

Choosing and Mixing Grout

  1. If you're re-grouting an old tile surface, remove the old grout. You can remove the old grouting compound with a grout saw or a grout removal bit in a rotary tool.[1] Make sure this is fully removed before proceeding.
  2. Pick a color of grout. The color of the grout will affect whether the eye notices the beauty of the individual tiles, or to the overall pattern of the tiles. Light grout tends to accentuate the individual tiles by blending in, becoming "invisible," while dark grout tends to accentuate the pattern of the tiles, their overall structure on the floor.[2]
    • Choose a color that matches the tile if you want the floor to have a continuous appearance. If you installed the tile yourself and the grout lines aren't perfectly straight, a matching color of grout can help conceal these imperfections.
    • Choose a color of grout that contrasts the tile color if you want the individual tiles to stand out. If you installed tiles with an irregular edge, a contrasting color of grout will enhance this feature of the tile.
    • Choose a dark color for high traffic areas. White or light-colored grout will be difficult to keep clean.
  3. Choose between sanded or unsanded grout. Sanded grout is stronger than unsanded grout. Sanded grout is needed when the grout lines are greater than 1/8-inch (3-mm) wide to add strength. Unsanded grout is liable to crack on wider joints.[3]
  4. Wait for the thinset mortar to cure. Thinset is used to adhere the tiles to the floor during installation. The exact drying time varies by brand, so read and follow the thinset packaging carefully. You usually have to wait at least a day to grout a tile floor.
  5. Mix the grout according to the package directions. You only want to mix as much as you can apply in about a half hour, as it will begin to dry out.
    • Dump the powder into a large bucket, and add only 3/4 of the recommended water, mixing thoroughly with a trowel. Afterwards, mix in the remaining 1/4 of water and mix again. It should be the consistency of thick batter; too much water will prevent it from hardening properly.

Applying the Grout

  1. Scoop some grout onto the tile floor with a trowel. Begin in the corner farthest from the doorway and work backwards.
  2. Spread the grout over a small joint. Hold a grout float at a 45-degree angle to the floor to press the grout into the joint. Move the grout float at a diagonal angle to the grout lines for a smooth finish. If you wipe parallel to the lines, the edge of the grout float can end up gouging out the grout.
  3. Remove excess grout. Your floor is full of muddy grout, which isn't a lovely sight. After applying, wait about 15 to 30 minutes for the grout in the joints to set. Then start cleaning:
    • Fill two buckets with the water.
    • Dip a large sponge with rounded corners into the first water bucket and wring it out.
    • Wipe in a circular motion or at a diagonal to the grout lines to remove excess grout from the surface of the tiles.
    • Rinse the sponge in the second bucket and repeat until all grout is removed from the surface of the tile.
    • Wait three hours before repeating the process again.
    • Make a final pass along the grout lines with the damp sponge to make sure the grout lines are smooth.
  4. Verify the grout color is what you want. Use a hairdryer to quickly dry this small area of grout, so you see how the color looks against the installed tile. Now is the time to make a last-minute change, as grout is nearly impossible to remove once it's dried.
  5. Continue with grouting if you are satisfied with the color. Keep working in small areas at a time, so you can remove the excess grout before it has a chance to dry. If you have a helper, one can grout and the other can remove the excess.
  6. Clean up the grout haze once everything is dry. No matter how effectively you cleaned the excess grout from the tiles, you're likely to have a "grout haze" covering your tiles after your job is done. To clean up the grout haze:
    • Take a dry towel or used rag and wipe at the haze until it begins to cake off. An old sock will work well: you can wear the sock on your hand while you scrub.
    • Brush up the residue with a broom.
  7. Wait for the grout to cure before sealing it. Read the manufacturer's directions to determine how many days to wait. To seal grout:
    • Crack the windows to get good ventilation in your room.
    • Pour a small amount of sealant on the grout and work it in with a sponge, using small, circular motions.
    • Wipe the sealant off after about 5 to 10 minutes, although the time may vary. Check the sealant label to be sure.
    • Re-seal the grout every six months to a year if possible.



Tips

  • Wear kneepads to grout a tile floor. You'll be kneeling on hard tile for extended periods. When using sanded grout, it can be quite abrasive on bare knees.
  • If plastic spacers were used between the tiles during installation, remove them before you grout (unless the manufacturer says they can be left in place).

Things You'll Need

  • Grout
  • Buckets
  • Trowel
  • Grout float
  • Large sponge
  • Kneepads

Related Articles

Sources and Citations