Make Paper from Old Scrap Paper
Recycle your old scrap paper by making it into interesting, one-of-a-kind paper paper that will make nifty notepaper, unique wrapping paper, or will enhance paper crafts you might be inspired to make. You'll need scrap paper, a blender or food processor, a fairly deep tub or basin (six inches deep, minimum), a mold and deckle (see "Tips" for making these yourself), cloth on which to "couch" the wet paper pieces (you can use white felt, white cotton interfacing, towels, etc.), and a sponge.
Contents
Steps
- Tear up your scrap paper into small (about one-inch) pieces and place into a blender or food processor.
- Fill the blender or processor with warm water.
- Blend the paper bits until the pulp is smooth; start blending on a slow speed and increase the speed as the pulp becomes smoother.
- Prepare a tub or basin that is deep enough to completely submerge your mold and deckle (See "Tips" for instructions to make a mold and deckle, the framework for your sheets of paper). Fill the tub or basin about half-full of water.
- Pour your pulp mixture into your basin. You should make several blender-loads of pulp to put into your basin in order to make multiple sheets of paper.
- Place your deckle (the frame) over the screen-side of the mold (the thing with the mesh screen) so that the edges of both the mold and deckle are even.
- Dip your mold and deckle into the basin with the screen facing up. You should dip the mold and deckle from the front to the back of the basin so that the pulp in the basin can settle onto the screen. Swirl your mold and deckle around until an even layer of pulp has settled on the screen. Hold the deckle steady on the mold!
- Holding the mold and deckle parallel to the water, lift them out of the basin and hold them there to let the water drain through the mesh.
- When most of the water has drained, lift your deckle carefully off the mold.
- Gently flip your mold over onto your cloth, with the pulp-side facing the cloth. Use a rolling motion - placing one side of the mold down, then the middle, then finally the opposite side - to place your mold face-down on the cloth.
- Through the screening of your mold, which is face-down on your couching cloth, use a sponge to dab excess water from the pulp. Sponge through the mold's screening.
- When you have sponged all the water you can from the paper pulp, very gently lift your mold off the couched pulp, starting with the edges. Lift the mold slowly, or your wet paper might tear or come up with the mold. (Your aim is to leave a wet piece of paper on the couching cloth when you lift the mold.)
- Place another cloth on top of your freshly-pulled paper sheet, and press it. You can either press it by hand or by placing something heavy on it. You can press multiple pieces of paper by stacking several freshly-pulled sheets (with cloth between each) and pressing them all at once.
- Once your paper is pressed and somewhat dry (it may still be damp, but not as fragile), you can hang it on a clothesline to finish drying. Or you can leave it to dry on the couching cloth, or on a smooth surface like glass or a mirror. You may wish to iron it smooth, or you can leave it as it is for added texture and character.
- Finished.
Tips
- Gel or liquid inks will not hold to written lines on this sort of paper (the ink spreads like water on a paper towel) unless you treat the paper. Once it's completely dry, brush it all over with a solution of gelatin and water and let it dry again.
- You can use cardboard, newspaper, old books, tissue paper, magazines, junk mail, typing paper, construction paper, unused napkins, old toilet paper rolls, and just about any other kind of unwaxed paper for this project.
- Your paper will be in the size and shape of your mold and deckle. You can make a mold and deckle with two picture frames (without the glass and backing) and some window screening: staple window screening to the outside edge of one picture frame to make your mold. Make sure the screening is taut across the frame. Fiberglass (as opposed to metal) screening works best. Trim excess screening from edges of the frame. Use a frame of the same size as your mold for your deckle.
- The cloth you couch your wet paper sheets onto will affect the finished look of your paper. Colored cloth may bleed color into your paper; if you use a towel, one side of your paper will be textured like the towel.
- If you plan to write on your paper, you might want to add some liquid starch (two or three teaspoons) to your pulp mixture for sizing. You can also use white glue, if you don't have liquid starch.
- For extra interest, you can add small bits of unblended paper to your pulp; I've had success adding small torn-up bits of an old book to smooth pulp to make interesting envelopes out of my paper. You can also add other inclusions, like bits of string or flower petals, to your smooth pulp.
- You can buy a mold and deckle from a paper maker supplier, and from some craft stores.
- Newspaper, tissue paper, and some other types of paper (like magazines) may alter the color of your paper (i.e., newspaper will give your finished paper a grayish cast).
- You can cover up the damp paper with a cloth towel and iron the paper.
- You can also make a mold out of a can - coffee can, bean can, whatever. Stretch your screening across the mouth of the can to make your mold and tack or staple it to the side of the can. Embroidery hoops can also be used to make a mold and deckle, in the same manner as the picture frame mold and deckle.
- Most homes, these days, have a paper shredder. Using the shredded paper will save the step of tearing the paper into {{safesubst:#invoke:convert|convert}} squares.
Warnings
- Any home shredder will probably have "window" envelopes in the mix. Your paper will have plastic pieces in it. Interesting as it may be, you may want to look out for that.
- Be cautious when using paper to keep from getting cut.
