Make a Homemade Fishing Rod
Store-bought fishing rods can be very expensive. For the casual fisher, it might be more cost effective to make your own. Start with Step 1 below to learn how you can make a homemade fishing rod from bamboo cane, some PVC pipes, or even a simple stick..
Contents
Steps
Making a Bamboo Fishing Pole
- Find a suitable piece of bamboo cane. Find a piece of bamboo cane that’s between 8 and 10 feet long and 1 and 2 inches in diameter and cut it at the base.
- When it comes to bamboo fishing pole, bigger is not necessarily better. Larger poles can be cumbersome to hold and awkward to transport.
- It’s probably best to cut three or four pieces of bamboo at a time, in case your first piece breaks after you’ve dried it out and you have to begin the process again
- Trim and smooth the cane. Use a small sharp knife to trim away any leaves or nubs, as close to the main body of the cane as possible.
- Find a joint at the thicker end of the cane and saw through it. This will ensure that the butt of your fishing pole has a closed end.
- Take a piece of sandpaper and used it to smooth the body of the fishing pole as much as possible.
- Leave the cane to dry. The next step is to dry out the cane pole. Tie a piece of string around the narrow end of the pole and suspend it from the ceiling. This will ensure that the cane dries evenly and as straight as possible.
- Dry the cane pole in a warm, dry place but do not exposed it to direct sunlight. Sunlight will dry out the cane too quickly, causing it to become brittle.
- Depending on temperature and humidity levels, the cane will take a few weeks to several months to dry out fully. You will know it’s ready when it turns a tan color.
- When the cane is dry pick it up and give it a few test swings through the air to make sure it doesn’t break or bend. If it does, try another piece.
- You want your fishing pole to be as straight as possible, so if it dries with a slight curve you can straighten it out by weighting it with bricks.
- Attach the fishing line. Take some 20 pound Dacron line and tie one end a couple of inches above the “handle” of the fishing pole.
- Run the line along the length of the pole until you get to the end. Then take some extra pieces of fishing line and use them to tie the running line to the fishing pole at two or three different points (including the tip).
- Be careful when tying the running line to the pole -- if it’s tied too tightly you won’t be able to slide the line up and down, but if it’s tied too loosely the line will droop and get tangled. Use a whip-finish if possible.
- The length of the fishing line (from the tip of the pole) should measure the total length of the pole, plus an extra two feet. If you prefer, the extra two feet can be monofilament leader instead of the Dacron line.
- Attach the hook, bobber and sinker. Attach your preferred hook or lure to the end of the line along with a bobber and a split-shot sinker.
- Now your homemade bamboo fishing pole is ready to use! To shorten the line, pull it back through the loops and wrap the excess around the handle.
Making a PVC Fishing Rod
- Cut two PVC pipes. Take two pieces of PVC piping -- one ½ an inch in diameter and the other ¾ of an inch.
- Use a saw to cut the PVC pipes to the desired length. Keep in mind that the combined length of the two PVC pipes will be the approximate length of your finished fishing rod.
- For example, for a small child-size fishing rod you could cut each pipe to a length of {{safesubst:#invoke:convert|convert}}.
- Use some sandpaper to smooth the sawed edges and remove any markings from the body of the pipes.
- Attach the slip caps and threaded connectors. You will need two slip caps: one ¾ inch and one ½ inch fitting.
- You will also need a ¾ inch to ½ inch threaded connector (female/male) and a ½ inch to ½ inch threaded connector (female/female).
- These fittings are available very cheaply from the hardware store. Slip each fitting onto the corresponding piece of pipe, but do not glue in place.
- Drill holes into the smaller PVC pipe. Take a power drill with a {{safesubst:#invoke:convert|convert}} drill bit and drill 3 to 5 holes all the way through the ½ inch PVC pipe.
- The number of holes will depend on the length of the pipe you are using. No matter how many holes you make, ensure that they evenly spaced.
- Attach the eyelets. Take a number of medium sized binder clips (to match the number of holes you drilled) and remove the silver wire from the clip.
- Use a pliers to bend one leg of the silver wire across the other. When you’re done, there should be a closed loop on one end of the wire and on the other end the legs should point inwards towards each other. Repeat with the other wires.
- Take a wire and clip the legs into the holes on either side of the ½ inch pipe. The loop at the end of the wire forms an eyelet for the fishing line. Repeat with the other wires.
- Attach a premade fishing reel to the larger pipe. Buy a premade fishing reel and attach it to the side of the larger ¾ inch PVC pipe.
- You can do this by using the same drill bit as before to make two holes in the side of the pipe, then screw the fishing reel into place
- Screw the PVC pipes together. The last step is to screw the two pieces of PVC pipe together to form your fishing rod and run the fishing line through the eyelets. Attach a hook, bobber and sinker to the end of the line.
- The great thing about this fishing rod is that you can remove the slip caps from either end of the rod to store tackle or anything else you want!
Making a Simple Fishing Pole for Kids
- Find a sturdy stick. Find a sturdy, straight stick that’s approximately {{safesubst:#invoke:convert|convert}} long and an inch or two in diameter. Remove any leaves or branches and use sandpaper to remove any knobbly bits, if necessary.
- Attach string and fishing line. Take a piece of string that’s about {{safesubst:#invoke:convert|convert}} long and tie it to the narrower end of the stick, about {{safesubst:#invoke:convert|convert}} from the end.
- Make sure the knot is nice and tight. Wrap the remaining string around the end of the stick.
- Tie two to three feet of thin fishing line to the end of the string, as this will make it easier to attach the hook.
- Tie a small hook to the end of the line. Thread a small fishing hook onto the end of the line. When it’s time to fish, unwind enough string from the end of the pole for the hook to reach the required depth.
Tips
- The simple stick fishing rod described in Method 3 above is best for catching {{safesubst:#invoke:convert|convert}} fish in small creeks and streams. Kids can use things like worms, raw bacon and hot dog pieces for bait.
Related Articles
- Build a Fly Rod
