Remove Lipstick From Carpet

Although your favorite shade of lipstick may look great on your face, it probably does not look as good on your carpet. If your child got a hold of your lipstick, or you accidentally stepped on a dropped tube, grinding it into the carpet, act fast to remove it. The sooner you begin the attempt, the easier removal will be.

Steps

Removing Stains with a Cleaning Product

  1. Remove large pieces of lipstick. Use a spoon or dull knife to carefully scrape and remove any large pieces of lipstick from the carpet. Try to avoid pushing the pieces further into the carpet.
  2. Test a cleaning product on a corner of your carpet. Lipstick stains attach to the carpet fibers with grease, so you will need a cleaning product that dissolves grease or oils.[1] Most all-purpose stain removers will work, as will dry cleaning fluid. However, these may discolor your carpet. Apply the cleaning product to an inconspicuous corner of the carpet first and let sit five minutes before blotting dry with a clean cloth. If the discoloration is severe, you may wish to find another product.
    • Dry cleaning fluid is especially likely to discolor your carpet.[2]
    • If you do not have any stain removers or dry cleaning fluid, see the section on alternate cleaning solutions for other products or homemade mixtures you may have access to.
  3. Blot with the cleaning product. Apply the cleaning product to a clean sponge or cloth. Press repeatedly over the stain, switching to a clean side if the cloth becomes heavily stained. Avoid rubbing, which may work the lipstick further into the carpet fibers or spread it to a wider area. Depending on the cleaning product, lipstick, and freshness of the stain, this step may remove the lipstick on its own.
    • Alternatively, you may spray the cleaning product onto your carpet and let sit five minutes before blotting. This may be more effective at removing the stain, but has a greater risk of discoloring your carpet.
    • Even if the stain is removed, skip to the end of this section for instructions on cleaning up traces of the solvent.
  4. Repeat if you are seeing good results. If most of the stain has been removed, launder or rinse out the sponge or cloth, then apply more of the same cleaning product and blot. Two or three attempts may be enough to remove the stain, although you should stop and choose another product in the alternate cleaning solutions method if you see no major improvements.
  5. Hand wash the cleaning product and stain remnants. Whatever product you used, wash your carpet afterward to remove traces of cleaning product that could discolor your carpet or damage its fibers. Hand wash the area with a white cloth and a small amount of laundry or dish detergent mixed with warm water. Depending on how much stain is left, you may opt to use only a few grains of detergent in a glass of water; use 1/4 teaspoon (1 mL) for a stronger mix or even form a granular paste that you can rub thoroughly against the carpet.[3][1]
    • Check the detergent ingredients first. Avoid products that contain lanolin or bleach, as these may damage your carpet.[3] If you're uncertain, test the product in an inconspicuous area of the carpet, such as a corner usually underneath furniture.
    • If you do not own detergent, skip to the next step.
  6. Rinse and dry the area. Rinse the carpet with clear, cool water, then blot it dry with a clean cloth. This should remove the detergent along with the traces of cleaning product and stain it picked up.
    • If the last residual traces are persistent, you may need to blot several times. Alternatively, leave a few wet paper towels in the area, weight them down with a heavy object, and wait for them to dry.[3]

Other Cleaning Solutions

  1. Use these options in place of commercial cleaning products. The basic cleaning section gives instructions for applying any cleaning product. If you use any of these solutions, follow the instructions in the cleaning section, blotting the carpet with a sponge or cloth dampened with one of these materials instead of a commercial product.

Rubbing Alcohol

  1. Sponge the stain with rubbing alcohol. Rubbing alcohol, or isopropyl alcohol, is a powerful grease solvent, and may be your best bet if a commercial cleaning product does not work. Be careful not to use too much alcohol, as it could reach the backing of the carpet and damage it.[3]
    • Avoid circular motions while rubbing, which could damage the carpet texture by tearing its fibers.
    • If you do not own rubbing alcohol, skip to the next step. It may be necessary to purchase some if you have persistent stains, however.

Nail Polish Remover

  1. Remove stains with nail polish remover. Check that the nail polish remover is pure acetone, as other ingredients may have unexpected results on your carpet. While you are unlikely to suffer any harm when exposed to small amounts of acetone on skin or inhaled as fumes, it's a good idea to work in a ventilated are and keep the acetone product away from children and pets.[4]
    • You may apply acetone directly to the stain and let sit five minutes before blotting.[5] Test in a less obvious corner of the carpet first to check for damage or discoloration.

White Vinegar

  1. Try white vinegar. Vinegar contains a small quantity of acetic acid, which can be effective at dissolving grease. Only use white vinegar, not a dark or red variety, or you may add an additional stain.

Hairspray

  1. Use hairspray if rubbing alcohol is not available. One of hairspray main ingredients is alcohol, but as with any complex product not intended for cleaning, the other ingredients could have an unpredictable effect. If other methods do not work and you do not have rubbing alcohol, spray a small amount of hairspray onto the stain and let it sit for 10 to 15 minutes. Wipe the area with a wet, warm cloth.

Windex

  1. Spot check for discoloration in an inconspicuous area.
  2. Stream spray if you can. However, if the stain has spread, then use the spray application.
  3. Dab until the stain disappears. Blot with water to diffuse the cleaning solution.

Bleaching to Hide Stains

  1. Use 3% hydrogen peroxide to hide stains that blotting won't pick up. This method is best used to bleach the last traces of stain after you have removed the majority of it with other methods. Hydrogen peroxide can be found at most drug stores, although you should check the labeling to make sure it is a 3% solution. Weaker solutions (lower percentages) will not be as effective, while stronger ones could damage your carpet.
  2. Test old hydrogen peroxide to see if it still works. An old bottle of hydrogen peroxide may have lost its potency, breaking down into water and oxygen. Pour a small amount onto your sink basin; if it fizzes, it is still effective.[6]
  3. Moisten the carpet tufts. Apply just enough hydrogen peroxide to wet the stained tufts of the carpet. You may wish to use a clean, dry cloth or sponge to apply this, as pouring by hand could result in applying too much and bleaching unstained carpet as well.
  4. Check back after one hour. The hydrogen peroxide should lightly bleach the carpet tufts to hide the remaining traces of stain within one hour. You may add additional hydrogen peroxide if you see improvement, but the stain is not completely gone. There is no need to rinse the carpet afterward, since the hydrogen peroxide will break down into water.



Tips

  • The quicker you act to remove the lipstick from the carpet, the greater your chance of success. If the lipstick has been on the carpet for a long time or has been aggressively ground into the carpet fibers, you may not be able to remove it entirely.

Warnings

  • Before trying any product on your carpet, it is important to first test it on an inconspicuous area of the rug to be sure that it does not damage or change the color of the carpet.
  • Avoid using more water or other liquid than required. You typically only need a damp sponge to cover the stained area; stop and squeeze the sponge or cloth over the sink if a large amount of liquid is pooling on your carpet.

Related Articles

Sources and Citations